Skip to main content

DeWalt DCS391 Parts (DCS391 Type 1)

1 Compatible Accessory Available!

Enhance your DeWalt DCS391 Type 1 with our range of accessories

CLAMSHELL SET
£25.96
MOTOR COVER
£11.39
Not Available
£0.00
SCREW
£1.92
SCREW
£1.92
BRAND LABEL
£1.92
HEX KEY 5 MM
£1.92
SWITCH SA
£70.83
BUTTON LOCK-OFF
£16.48
SCREW
£1.92
SPRING
£2.96
PIN
£1.92
SPINDLE SA
£30.26
GASKET
£1.92
SCREW
£1.92
WIPER
£1.92
SPINDLE LOCK
£1.92
SPRING
£1.92
20 N086228
GUARD UPPER
£30.26
BUMPER
£1.92
SCREW
£1.92
SPIROL PIN
£1.92
GUARD LOWER
£17.89
25 N035365
SPRING
£1.92
RETAINER
£1.92
SHOE SA
£51.66
LEVER
£2.29
SHAFT
£6.52
SCREW
£1.92
31 N112241
WASHER
£1.92
CARRIAGE BOLT
£1.92
KNOB
£4.48
34 N022876
CARRIAGE BOLT
£1.92
SCREW
£1.92
SPRING
£1.92
KNOB
£1.92
WASHER INNER CLAMP
£6.52
WASHER OUTER CLAMP
£3.98
BLADE BOLT
£3.98
BEARING
£5.35
ARMATURE SA
£45.03
MAGNET
£0.00 Not Available
46 N171820
SUPPORT BEARING
£0.00 Not Available
BEARING & SEAL
£4.48
BAFFLE
£5.35
BRUSHBOX SA
£8.45
SCREW
£1.88
GEARCASE SA
£46.92
SCREW
£1.92
71 N107523
RATING PLATE
£1.67 Not Available
72 N104672
DUST PORT
£6.52
73 N106370
SCREW
£1.92
800 761995-01
GREASE
£45.03
856 381091-01
GUIDE FENCE
£4.48
861 N153976
KITBOX
£77.38
862 605265-00
SPRING CLIP
£12.69
866 N195933
BATTERY 18V - 4.0AH - 72WH
£214.91
871 N120341
CHARGER 10.8V - 18V
£89.87

The DeWalt DCS391 is a cordless 165mm circular saw from the 18V XR range, designed for cutting timber, sheet materials and other common construction materials. With a compact cordless design, 55mm maximum cutting depth at 90° and bevel adjustment up to 50°, it is suited to general cutting work where portability is important.

If your DCS391 is not working, has developed excessive play, is cutting inaccurately or has a problem with the blade guard, spindle, switch or motor, the individual components can be identified through the DeWalt DCS391 parts list and diagram.

DCS391 Parts Diagram and Parts List

The DCS391 parts diagram shows the saw broken down into its main mechanical, electrical and housing components. This is particularly useful when a repair involves a small component that is difficult to identify from the assembled saw.

The parts breakdown includes the clamshell housing, motor cover, switch, lock-off button, spindle assembly, spindle lock, upper and lower guards, springs, pins, screws, blade-drive components and guide fence. There are also numerous smaller components used throughout the saw.

DeWalt has produced the DCS391 in several Type versions, including Type 1, Type 2, Type 10 and Type 11. The parts listings show that some components, particularly switches and smaller electrical or housing parts, can differ between versions, so checking the Type number before ordering is important.

DCS391 Motor and Electrical Parts

If your DeWalt DCS391 will not start, the electrical system is one of the first areas to investigate. The parts catalogue includes the switch assembly, lock-off button, springs and associated electrical components.

The DCS391 switch is available in different part-number configurations depending on the Type of saw. For example, Type 1 uses switch part N189271, while later Type listings show different switch assemblies.

If the saw is completely dead, starts intermittently or only operates when the trigger is held in a particular position, the switch and surrounding components should be checked. Battery condition and the battery connection should also be ruled out before dismantling the saw.

DCS391 Spindle and Blade Drive Parts

The spindle is responsible for transferring the motor's rotation to the circular saw blade. The parts list identifies the 659417-00 spindle assembly, together with the spindle lock, gasket, wiper, screws and other components surrounding the blade-drive mechanism.

If the DCS391 blade is wobbling, does not run true or the spindle lock is not operating correctly, these components should be inspected. Wear or damage around the spindle and blade mounting area can affect cutting accuracy and should not be ignored.

The inner clamp washer is also separately identified in the parts information, providing another individual component that can be replaced if damaged or missing.

DCS391 Blade Guard and Safety Components

The upper and lower blade guards are important parts of the DCS391's cutting assembly. The parts breakdown identifies the N086228 upper guard and 611925-00 lower guard, along with springs, pins, retainers, bumper and associated fasteners.

If the DCS391 blade guard is sticking, does not retract properly or fails to return around the blade, inspect the guard mechanism rather than simply lubricating or forcing it. A damaged spring, pin, retainer or guard component can affect the movement of the assembly.

The spindle lock is also separately listed, making it possible to investigate problems with blade changes without assuming the entire saw requires replacement.

DCS391 Guide Fence and Cutting Adjustment Parts

The guide fence helps maintain a consistent cutting line when making straight cuts. A replacement DCS391 guide fence is available as an individual component, along with the associated mounting hardware.

If the saw is cutting inaccurately, check that the guide fence is secure and that the base and adjustment mechanism are correctly aligned. Problems with the fence, base or blade mounting can all affect the finished cut.

The DCS391's bevel mechanism also allows the saw to be adjusted for angled cuts, so mechanical components around the base and adjustment points should be checked if the saw no longer holds the required angle.

DCS391 Carbon Brushes and Motor Components

Unlike newer brushless DeWalt circular saws, the DCS391 parts listings include a brush assembly, meaning the motor uses replaceable carbon brushes. A brush assembly is listed as part 610126-00 for the DCS391.

If the saw has become intermittent, produces excessive sparking or has lost power under load, the carbon brushes are worth inspecting. Worn brushes can affect the motor's ability to maintain consistent contact with the commutator.

The motor cover and end-cap components are also separately identified, allowing the motor area to be serviced without necessarily replacing the complete housing.

DCS391 Housing, Spindle Lock and Small Parts

The DCS391 contains many smaller service components that are easy to overlook when carrying out a repair. These include springs, pins, screws, washers, retainers, gaskets and the lock-off mechanism.

The clamshell set, for example, is listed as N064324, while the motor cover is N054423. Other individual components include the 605107-00 lock-off button, 389120-00 spring and 388531-00 pin.

Replacing a small damaged or missing component can sometimes resolve a mechanical problem without needing to replace a larger assembly.

Finding the Correct DeWalt DCS391 Parts

When searching for DeWalt DCS391 parts online, always check the Type number printed on the saw before ordering. DeWalt's own parts system uses the model and Type number to identify the correct diagram and parts list, and the DCS391 has several Type versions.

From the DCS391 switch and carbon brushes to the spindle, blade guards, spindle lock, guide fence, housing and smaller springs and pins, matching the component to the correct DCS391 parts diagram is the best way to identify the part needed for your repair.

Accessories for DeWalt DCS391 Type 1

Circular Saw Blade - MT1652024

Circular Saw Blade for Bosch GKS 36 V-LI Circular Saw 24 t.c. teeth 165mm x 1.7mm x 20mm A bubget price alternate thin kerf bevel toothed ripping blade for cutting solid wood down the grain
View full description →
Price:  £12.95

This model also has 1 accessories available.

Scroll down to view them.