Skip to main content

Makita DTD153 Parts

HOUSING SET
£12.35
RUBBER PIN 6 DUR/DHR/DTW/DG
£1.00
HEX LOCKING NUT M4-7 MT/TD126
£1.00
DTD153 NAME PLATE
£1.00
TAPPING SCREW 3X16 TD126/DUM
£1.00
F/R CHANGE LEVER DTD148/DTD154
£1.00
SWITCH COMP DTW181/ DTD154
£14.45
ROTOR
£17.05
STATOR
£9.15
LED CIRCUIT
£5.95
TERMINAL DHP480/DDF480/DFL650
£4.25
RING SPRING 11 BTD/TD126/TL064
£1.00
NARROW WASHER 12 TD126/DTD154
£1.00
COMPRESSION SPRING 13 TD126
£1.00
BIT SLEEVE BTD134/146/136/147
£2.35
BUMPER
£1.00
HAMMER CASE COMPLETE
£10.25
NYLON WASHER 19 BTD134/TD126
£1.00
STEEL BALL 3.5 TD126
£1.00
ANVIL M
£7.05
HAMMER
£7.15
FLAT WASHER 24 HR1840/HR1841F
£1.00
COMPRESSION SPRING 25
£4.45
STEEL BALL 5.6 TD126/DTD154
£1.00
SPUR GEAR 22 BTD134/136/132/1
£4.45
SPINDLE DTD152
£7.65
PIN 5 BTD134LF10/TD126
£1.00
THIN WASHER 15 HR3000C/DTD154
£1.00
INTERNAL GEAR 51
£1.95
O RING 48 HM1110/1110/1HR2510
£1.00
O RING 40 BTD134/136/144/146/
£3.15
BEARING BOX COMPLETE
£4.35
TAPPING SCREW PT 2X6 DJV
£1.00
FLAT HD SCREW M3X6 DTD170/863L
£1.00
CONTROLLER
£66.15

Makita DTD153 Spare Parts

The Makita DTD153 is a compact 18V LXT brushless impact driver built for fast, repetitive fastening where a full-size drill can be awkward to use. With a 1/4" hex drive, up to 3,400rpm and 170Nm of maximum torque, it packs a lot of performance into a short 126mm body.

Because the DTD153 uses a brushless motor, carbon brushes aren't one of the parts you'll need to worry about replacing. Instead, faults are more likely to involve the impact mechanism, gearbox, electronics, switch or front-end components. The Makita DTD153 parts diagram above provides a useful reference for identifying the individual components.

DTD153 Hammer and Anvil

The hammer and anvil are among the most important components to consider if your DTD153 has started making unusual noises, isn't delivering its usual impact or is struggling to transfer torque to the fastener. The hammer case contains the anvil, hammer, steel balls, springs and washers that create the impact action.

The anvil and hammer are available as individual parts, so wear in the impact mechanism doesn't necessarily mean replacing the complete front assembly. This can be particularly useful on a DTD153 that has seen years of heavy fastening work.

DTD153 Gearbox and Spindle Repairs

If the driver is grinding, vibrating excessively or losing performance under load, the gears and spindle are worth investigating. The DTD153 contains a spur gear, internal gear, spindle, bearing box and several O-rings and other transmission components.

Wear in one of these parts can affect the way the impact mechanism operates. The spindle, gears and bearing box can be identified individually using the parts diagram, allowing you to concentrate the repair on the affected section.

Brushless Motor and Controller

The DTD153's brushless motor consists of a rotor and stator controlled electronically, rather than using traditional carbon brushes. If the impact driver won't start, cuts out or has developed an intermittent electrical fault, the controller, rotor, stator, switch or battery terminal are worth checking.

The controller is particularly important on this model, as it manages the electronic operation of the brushless motor. A driver that appears completely dead therefore shouldn't automatically be assumed to have a failed motor.

Switch, LED and Housing Components

The switch and forward/reverse change lever receive plenty of use on an impact driver. A trigger that doesn't respond correctly or a damaged direction lever can often be dealt with by replacing the relevant component rather than the complete tool. The DTD153 also has a separate LED circuit and battery terminal.

For a tool regularly used on site, physical damage is another consideration. The housing set, bumper, bit sleeve and smaller pins, springs and fasteners are all represented in the DTD153 parts information.

Find the Correct DTD153 Part

Use the Makita DTD153 parts diagram above to locate the component associated with your repair, then match the reference number against the DTD153 parts list to confirm the correct Makita part number.

From DTD153 hammers, anvils and spindles to gears, bearings, controllers, switches, LED components and housing parts, a wide range of individual Makita DTD153 replacement parts can be used to repair a well-used impact driver. Replacing the component that has actually failed can often be a much more practical solution than replacing the complete machine.