Skip to main content

Makita DTD171 Parts

A01 266622-8
TRUSS HEAD SCREW M4X12/BAP182
£1.00
Housing Set
£0.00
A02 346317-0
Belt Hook Clip
£2.36
NYLON WASHER 30 DTD171
£1.00
HAMMER DTD171
£32.75
COMPRESSION SPRING 24B DTD171
£3.95
SPINDLE DTD171
£50.65
27-1 253445-3
FLAT WASHER 15 HR3000C/DTD154
£1.00
*CONTROLLER DTD171
£84.40
REAR COVER DTD171
£3.95
*HOUSING SET DTD171
£22.25
SWITCH UNIT DTD171
£11.75
F/R CHANGE LEVER DTD148/DTD154
£1.00
SWITCH COMPLETE DTD171
£22.55
SEAL BTD136/147
£1.00
RING SPRING 11 BTD/TD126/TL064
£1.00
NARROW WASHER 12 TD126/DTD154
£1.00
COMPRESSION SPRING 13 TD126
£1.00
BIT SLEEVE BTD134/146/136/147
£2.35
BUMPER DTD171
£2.05
HAMMER CASE COVER DTD171
£1.85
HAMMER CASE COMPLETE DTD171
£31.95
O RING 12 AN504/HM1203/HM1213
£1.00
ANVIL ASS'Y DTD171
£26.15
020-1 216040-0
STEEL BALL 3.5 TD126
£1.00
STEEL BALL 3.5 BPJ/DTD154/TL06
£1.00
FLAT WASHER 24 HR1840/HR1841F
£1.00
STEEL BALL 5.6/DTW285
£1.00
SPUR GEAR 22 DTD148/DTD154
£5.75
PIN 5 DTD148/DTD154/DTD170
£1.00
THIN WASHER 15 HR3000C/DTD154
£1.00
INTERNAL GEAR 51 DTD171
£6.55
O RING 40 BTD134/136/144/146/
£3.15
BEARING BOX COMP DTD154
£5.55
TAPPING SCREW PT 2X6 DJV
£1.00
032-1 620D48-6
CONTROLLER DTD171
£84.40
FLAT HD SCREW M3X6 DTD170/863L
£1.00
STATOR DTD170/DTD154
£15.15
ROTOR DTD154
£42.95
TAPPING SCREW BIND 3 X 16 L14
£1.00
LED CIRCUIT DTD171
£8.75
039-1 183N06-8
HOUSING SET DTD171
£14.45
RUBBER PIN 6 DUR/DHR/DTW/DG
£1.00
HEX LOCKING NUT M4-7 MT/TD126
£1.00
SWITCH PLATE COMPLETE DTD171
£3.95
TERMINAL DHP480/DDF480/DFL650
£4.25

The Makita DTD171 parts diagram provides a detailed breakdown of the impact driver and its individual components. This is particularly useful when identifying internal parts that are difficult to distinguish once the tool is assembled.

The parts list includes the hammer case, hammer, anvil assembly, spindle, internal gear, spur gear, stator, rotor, controller, LED circuit, switch unit and housing assemblies. There are also numerous springs, O-rings, washers, steel balls, pins and screws.

Matching the numbered position on the diagram with the corresponding part number makes it easier to identify the correct DTD171 parts for your repair.

DTD171 Hammer, Anvil & Impact Mechanism Parts

The impact mechanism is central to the operation of the DTD171, converting the motor's rotation into the repeated impacts needed for high-torque fastening.

The parts breakdown includes 327114-3 hammer, 136065-7 anvil assembly, 327113-5 spindle, compression springs, steel balls and associated washers and retaining components. The hammer case is also available as a complete assembly, with 140A51-8 hammer case complete listed for the model.

If your DTD171 has stopped impacting, is producing weak impacts or is making unusual noises during fastening, the hammer, anvil, spindle and associated spring components are worth investigating.

Makita DTD171 Gearbox & Spindle Parts

The drive mechanism contains several gears and bearings that transfer the brushless motor's output to the impact assembly. Heavy fastening work can place considerable mechanical load on these components.

The parts list includes 226182-2 internal gear 51, 227338-0 spur gear 22, 327113-5 spindle, bearing components and O-rings. The gearbox also contains a number of smaller washers, pins and steel balls that work together within the impact mechanism.

If the Makita DTD171 is noisy, has excessive play or is not transferring power correctly, the gears, spindle and supporting components should be checked.

DTD171 Brushless Motor, Rotor & Stator Parts

The DTD171 uses Makita's brushless motor technology, so it does not have conventional carbon brushes that require periodic replacement. Instead, the motor assembly consists of the rotor, stator and electronic control system.

The parts breakdown identifies 629217-2 stator and 619408-3 rotor, together with the controller and associated electrical components.

If the DTD171 has power but will not run, cuts out during operation or has developed a motor-related fault, the battery, terminal and switch should be ruled out before investigating the brushless motor and controller.

Makita DTD171 Switch & Controller Parts

Electronic control is an important part of the DTD171, with the tool providing multiple speed and torque settings for different fastening applications. The parts list includes 632L84-8 switch unit, 140B49-1 switch complete, 455053-8 forward/reverse change lever and controller 620848-0.

If your DTD171 will not switch on, operates intermittently or the controls are not responding correctly, the switch and controller are among the components that can be investigated.

The DTD171 also incorporates an electronic four-speed system, allowing the tool to be adjusted for different fastening tasks.

DTD171 LED Circuit, Housing & Battery Terminal Parts

The DTD171 features dual LED lights to illuminate the work area, and the parts breakdown identifies 620849-8 LED circuit as a separate component. The tool also includes replaceable housing sections and battery connection components.

The parts listings identify housing assemblies 183K87-4 and 183N06-8, together with 643860-3 terminal and rear cover 458478-5.

If the DTD171 battery connection is loose, the casing is damaged or the LED lighting has stopped working, individual components can be checked against the parts list rather than automatically replacing the complete tool.

Smaller Makita DTD171 Replacement Parts

The DTD171 contains numerous small components that are important to the operation of the impact mechanism. These include O-rings, compression springs, ring springs, steel balls, flat washers, pins and screws.

For example, the parts breakdown identifies 232459-5 compression spring, 213507-9 O-ring 40, 216011-7 steel ball, 267175-0 flat washer and 268311-1 pin. These smaller Makita DTD171 replacement parts can be particularly useful when rebuilding the front mechanism or repairing a well-used impact driver.

Identifying the Correct DTD171 Spare Parts

When searching for Makita DTD171 parts online, check the model carefully before ordering. The DTD171 has been supplied in several versions including DTD171Z, DTD171RTE and other market-specific variants, although the relevant parts diagram can be used to confirm the components fitted to the machine.

Whether you need a DTD171 hammer, anvil, spindle, gear, rotor, stator, controller, switch, LED circuit, housing, battery terminal or smaller mechanical part, matching the part number to the correct diagram is the best way to identify the component required.

Using the correct Makita DTD171 spare parts allows individual worn or damaged components to be replaced while keeping this compact 18V LXT impact driver in service.