Skip to main content

Makita DUN500W Parts

A01 125516-5
*BAND ASSEMBLY DUR365
£5.82
A02 458413-3
BLADE COVER 500 DUH501
£24.50
A03 450128-8
BATTERY COVER BDG800/DTW251
£1.00
E01 807E85-5
LABEL/SOUND 92DB DUR364
£1.00
HOUSING SET DUN500W
£6.65
MOTOR HOUSING SET DUN500W/600L
£3.05
TAPPING SCREW PT 2X6 DJV
£1.00
CONTROLLER B DSL800
£14.35
FLAT HD SCREW M3X6 DTD170/863L
£1.00
STATOR DUH501/601/751
£23.85
BALL BEARING 695ZZ DUR187L/188
£2.15
ROTOR ASSY DUN500W/600L
£16.95
BALL BEARING 608DDW GA5020
£6.15
O RING 22 BBC231/UX360/DUX60
£1.00
SWITCH UNIT DUN500W
£8.65
GEAR HOUSING COMPLETE DUN500W
£35.95
HEX LOCK NUT M5-8 BO3710/3711
£1.00
FLAT WASHER 25 DHR164/HR1840
£1.00
SLEEVE 6 DUN500W
£1.00
ANGULAR HOLDER DUN500W
£1.95
HS BUTTON HD BOLT M5X16 AN611
£1.00
PIPE HOLDER COVER 24 DUN500W
£12.95
STOPPER PIN DUN500W
£2.05
PAN HD SCREW M4X20 9032/LS081
£1.00
STOPPER PIN HOLDER DUN500W
£1.75
COMPRESSION SPRING 5 AN451
£1.00
EXT E-RING JIS E-4 EA3201
£1.00
COMPRESSION SPRING 5 DST111&2
£1.00
PIPE HOLDER 24 DUN500W
£19.75
FLAT WASHER 45 DUN500W
£3.21
SIDE COVER DUN500W
£4.95
H.S.B. HEAD BOLT M5X60 WITH WR
£1.00
SLIDE GRIP 24 DUN500W
£2.65
SHEAR BLADE 500 SET DUN500W
£150.60
GREASE VESSEL SET(D)
£13.15
Price on application
£1.00
PAN HD SCREW M5X10 W/CP WASHE
£1.00
SEAL EH7500/EN4951SH/HT2360D
£5.35
SLEEVE 5 DUH501/601/751
£1.00
H.S.H.BOLT M5X25 WITH WR
£1.00
HELICAL GEAR 68 DUN500W/600L
£14.35
CONNECTING ROD DUH604S/754S
£4.85
NEEDLE CAGE 315 DUH604S/754S
£4.85
PLATE DUN500W/600L
£1.00
FRICTION PLATE DUH501/601/751
£1.00
GEAR HOUSING GASKET
£2.05
GEAR HOUSING COVER
£17.45
HEX SOCKET BOLT M4X16 EH7500
£1.00
H.S.BUTTON HEAD BOLT M6X4
£2.85
PIPE 24 COMPLETE DUN500W
£24.75
CAUTION LABEL DUN500W/DUN600L
£1.00
HANGER BBC231U/BBC300L/BUX360
£4.75
HEX BOLT M5X18 DUR188L
£1.00
SUB CONTROLLER COMPLETE
£24.05
SWITCH LABEL
£1.00
SWITCH UNIT DUR364/DUR187/188
£12.15
SWITCH UNIT DUC254
£10.75
LOCK OFF LEVER DUX60
£2.55
COMPRESSON SPRING 4 4304/DUX60
£1.00
CLAMP 24 ER2650/ER2550/EN4951
£1.00
SWITCH LEVER DUN500W/600L
£1.85
TORSION SPRING 10 DUR182/365
£2.65
RUBBER PIN 6 DUR/DHR/DTW/DG
£1.00
GRIP HOUSING SET DUN500W/600L
£22.65
HEX LOCKING NUT M4-7 MT/TD126
£1.00
CONTROLLER DUN500W
£116.65
TERMINAL DJR186/DUR187/DUR188
£3.45
TAPPING SCREW M4X18 EBH253/EB3
£1.00
BATTERY GUARD DUN500W/600L
£4.05
SPECIAL PAN HD SCREW M4X12
£1.00
SERIAL NO. LABEL DUN500W
£1.00
NAME PLATE DUN500W
£1.00

The Makita DUN500W is an 18V LXT cordless pole hedge trimmer with a 500mm cutting blade and adjustable cutting head. Its brushless motor, three-speed control, reverse rotation system and electric brake make it suited to maintaining taller hedges while keeping the operator at ground level. The head can be adjusted through multiple positions and folded for transport and storage.

If your DUN500W is not working, has developed a problem with the blade drive, is cutting out, or the adjustable head or pole mechanism is damaged, individual components can be replaced using the correct Makita DUN500W spare parts.

Makita DUN500W Parts Diagram and Parts List

The Makita DUN500W parts diagram above shows the machine divided into its main assemblies and individual components. This is particularly useful when identifying parts inside the motor housing, gear mechanism and long pole assembly.

The parts list includes the housing, motor housing, controller, stator, rotor, bearings, switch unit, gear housing, pipe holders, shaft components, blade drive parts and numerous springs, washers, pins and fasteners.

Because several components are similar to parts used on related Makita hedge trimmers, checking the exact DUN500W model and part number is important before ordering.

DUN500W Motor, Rotor and Controller Parts

The DUN500W uses a Makita brushless motor, so there are no conventional carbon brushes to replace. Instead, the motor system incorporates a stator, rotor and electronic controller.

The parts breakdown identifies the 629352-6 stator, 519598-1 rotor assembly and 620B02-8 controller. Bearings supporting the motor are also listed, including 211157-4 and 210005-4.

If your DUN500W has power but the motor is not running, cuts out or behaves erratically, the battery and basic controls should be checked first. Where an internal electrical fault is suspected, the controller, stator, rotor, switch and associated connections can be investigated.

DUN500W Gear Housing and Drive Parts

The motor transfers its power through the gear and drive mechanism to operate the long cutting blade. The DUN500W gear housing is separately identified as 140R17-0, with additional sleeves, pins, washers and other components supporting the drive system.

If the motor runs but the blade does not move correctly, or there is unusual noise or excessive movement around the drive mechanism, the gear housing and associated components may need inspection.

Smaller parts such as 257761-5 sleeve 6, 347656-1 angular holder and the various pins and washers can also be replaced individually where listed.

DUN500W Blade and Cutting Assembly

The 500mm blade is one of the most important service components on the pole hedge trimmer. The parts listing identifies the complete 191C14-9 shear blade set for the DUN500W.

The cutting assembly also contains a number of supporting components, including drive plates, washers, rings, pins and linkage parts. These components transfer movement from the drive mechanism into the reciprocating blade.

If the DUN500W blade is not moving, is damaged or has developed excessive movement, inspect the blade assembly and drive components rather than assuming that the motor itself has failed.

DUN500W Adjustable Head and Pole Parts

One of the key features of the DUN500W is its adjustable cutting head, which can be positioned for different hedge-cutting angles and folded for transport. The long shaft and pole assembly therefore contain several mechanical components that can wear or become damaged.

The parts diagram includes pipe holder 24 (319950-1), pipe holder cover 319952-7, side cover 319951-9, slide grip 412296-5, stopper pin 327514-7 and stopper pin holder 412295-7.

If the head is difficult to adjust, will not lock securely or has developed movement in the pole assembly, these components are worth checking.

DUN500W Switch and Electrical Parts

The DUN500W switch unit, part number 632P71-1, is another separately listed component. The machine also uses lead units and internal electrical connections between the controls, battery and motor electronics.

If your Makita DUN500W will not start, check the battery, terminals and operating controls before investigating the internal electrical components. A faulty switch or connection can prevent the brushless motor from receiving the required control signal.

Always remove the battery before dismantling or inspecting the hedge trimmer.

Housing, Guards and Smaller DUN500W Parts

The DUN500W contains numerous smaller components that can be replaced during a repair, including screws, springs, washers, rubber pins, covers and retaining parts. The main 183N85-6 housing set and 183N83-0 motor housing set are also separately identified.

External accessories and protective components include the blade cover and battery cover. Replacing a damaged cover, housing section or small fixing can be preferable to replacing an otherwise serviceable hedge trimmer.

Getting the Right Makita DUN500W Spare Parts

When ordering Makita DUN500W parts, check the model number and part number carefully against the parts diagram. This is particularly important for internal motor, electronic and drive components, where similar Makita machines can use different assemblies.

Whether you need a DUN500W shear blade, rotor, stator, controller, switch, gear housing, pole component, housing part or smaller mechanical component, the numbered parts list provides a useful reference for identifying the correct item.

With the right Makita DUN500W replacement parts, individual worn or damaged components can be repaired or renewed, helping keep this 18V LXT pole hedge trimmer working effectively for longer.