Skip to main content

Makita HM0860C Parts

TOOL HOLDER CAP HM0860C/HR3540
£1.85
CHUCK COVER HM0860C
£2.35
RING SPRING 25 HR5001C/HM1202C
£1.00
FLAT WASHER 28 HM0860C
£2.45
*URETHANE RING 28 HM0860C
£4.05
CHUCK RING HM0860C/870C/871C
£4.95
TOOL RETAINER HM0860C/0870C
£4.65
*SPRING GUIDE HM0860C/870C/871
£10.15
COMPRESSION SPRING 52 HM0860C
£1.00
*RING SPRING 50 HM0860C
£2.45
*PLATE HM0860C
£1.00
PLATE HM0870C/871C
£2.45
LOCK RING HM0860C/0870C/0871C
£9.05
CHANGE RING HM0860C
£3.15 Not Available
RETAINING RING/INT ROUND R-42
£4.55
RETAINING RING R-42 HR3000C
£1.85
FLAT WASHER 29 HM0860C
£1.00
*URETHANE RING 28 HM0860C
£4.05
RUBBER RING 28 HM0870C/781C
£2.45
STEEL BALL 4.8 TW100D/TD0101F
£1.00
TOOL HOLDER HM0860C/870C/871C
£51.15
O RING 38 HM0860C
£1.00
FLUORIDE RING 28 HM1202C/HR500
£10.45
O RING 23 HM1202C/HR5001C
£1.00
IMPACT BOLT HM0860C/870C/871C
£8.55
RUBBER RING 20 HM0860C
£5.55
CUP WASHER 23 HM0860C
£2.45
*BARREL HM0860C
£42.65
BARREL HM0860C
£55.15
CAP HD SCREW M6X30 8900N/LF10
£1.00
O RING 53 BO3710/3711/HM0860C
£1.95
*CHUCK RING HM0860C
£1.85
*CHUCK RING HM0860C
£1.95
GUIDE RING HM0870/71C
£3.25
*SLIDE SLEEVE HM0860C
£1.75
SLIDE SLEEVE
£2.65
SLIDE SLEEVE HM0860C/870C/871C
£2.85
'RING 36 HM0860C/870C/871C
£6.55
'COMPRESSION SPRING 37 HM0860C
£1.00
CYLINDER GUIDE HM0860C
£6.45
O RING GD0810C/GD0811C
£1.00
CRANK HOUSING COVER HM0860C
£8.95
'STRIKER HM0860C/870C/871C
£6.55
O RING 24 HM0860C
£2.35
'CYLINDER 32 HM0860C/870C/871C
£28.55
'RING SPRING 34 HM0860C
£1.00
'RING SPRING 34 HM0860C
£1.00
'RING SPRING 34 HM0860C
£1.00
FLAT WASHER 34 HM0860C
£8.05
CAP HD SCREW M5X25 HM0870/71C
£1.00
LABEL/MAKITA 500 4305HR160DW
£1.00
SWITCH BTM/3707F/3708F/DTM51
£8.05
'SWITCH LEVER HM0860C
£1.00
LEAF SPRING HM1110/HM1317C/CB
£1.00
RUBBER PIN 4
£1.00
SWITCH BOX HM0860C
£2.25
TAPPING SCREW 4X18
£1.00
'CRANK CAP HM0860C
£0.00 Not Available
SEAL RING HM0860C
£0.00 Not Available
PAN HD SCREW M5X20 W/CP WASHE
£1.00
PIN 8 HM0860C
£1.00
O RING 24 HM0860C
£2.35
O RING 26/6960DZ OIL UNIT COMP
£1.00
PISTON HM0860C
£1.95
CONNECTING ROD HM0860C/870C/71
£1.00
CRANKSHAFT COMP HM0860C
£38.55
FLAT WASHER 14 HM1317C-CB/HM
£1.00
CRANK HOUSING COMP HM0860C
£55.15
PT SCREW 5X25 KP0810C KP0810
£1.00
OIL SEAL 15 BHR262/HM1203/BHR
£5.65
SLEEVE 12 HR4500C/4511C/BHR26
£4.25
BALL BEARING 6201LLU HM0860C
£3.95
THIN HARD WASHER 12 JN3200
£1.00
BAFFLE PLATE HM0860C
£1.85
ARMATURE ASS 110V HM0860C
£47.15
ARMATURE ASS 240V HM0860C
£47.15
INSULATION WASHER HM0870/71C
£4.95
BALL BEARING 608DDW GA5020
£6.15
HANDLE HM0860C
£15.95
PAN HD SCREW M5X20 W/CP WASHE
£1.00
PT SCREW 5X25 KP0810C KP0810
£1.00
'SERIAL NO. LABEL HM0860C
£1.00
ACRYLIC PIN 5 HR4000C/HR3000C
£1.00
'HANDLE CAP HM0860C
£1.75
LEAD UNIT HM0860C
£2.15
CONTROLLER 240V HM0860C
£19.95 Not Available
CONTROLLER 110V HM0860C
£38.65
STRAIN RELIEF 110V UK360/HS61
£1.00
TAPPING SCREW 4X18
£1.00
CORD GUARD 10 HM1317C/CB/HR30
£2.25
*POWER SUPPLY CORD 1.5-2-4.0
£12.05
POWER SUPPLY CORD 1.5-2-4.0
£23.45
'FIX ROD HM0860C
£1.00
PT SCREW 5X60 HS7100/HM1317C
£2.25
FIELD ASS 110V HM0860C
£12.05
FIELD ASS 240V HM0860C
£12.05
'SUPPORT COMP HM0860C
£3.75
MOTOR HOUSING COMP HM0860C
£22.25
'NAME PLATE HM0860C
£1.00
TAPPING SCREW 4X18
£1.00
BRUSH HOLDER COVER HM0860C
£1.00
BRUSH HOLDER CAP 4100KB HS7611
£1.00
*AC CARBON BRUSH CB-304 HM1100
£9.15
*AC CARBON BRUSH CB-323
£9.15
AC CARBON BRUSH CB-327 (Pair)
£9.15
FAN 76 ASSY HM0860C
£4.25
WASHER 6 HR3000C/LF1000
£1.00
HEX NUT M6 9564/65CV/DZ&H
£1.00
'REAR COVER HM0860C
£3.75
TAPPING SCREW 4X18
£1.00
GRIP SPRING 60 HM0860C
£4.65
SQUARE BOLT M8X80 HM0860C
£1.85
100 418363-4
SIDE GRIP BASE 60 HM0860C
£2.55
101 152554-4
*GRIP 36 COMP HR3000/HR4000C
£8.45
102 152620-7
HANDLE BASE COMPLETE HM1100C
£12.05
103 252640-2
WING NUT M8 HM1100C/HM1200K
£6.55
104 265439-6
HEX HD BOLT M8X150
£2.15
105 417002-3
SIDE HANDLE CAM HM1202C/HR4500
£1.75
106 417003-1
SIDE HANDLE HM1202C/1110/1111
£8.65
1001 181573-3
GREASE VESSEL 93G
£5.24
1001 194683-7
Grease vessel set, 100 ml
£7.60
1002 824708-0
PLASTIC CARRYING CASE
£49.22
5001 655030-2
PLUG UK TYPE 16A-4H/110V
£8.34
5002 654091-9
NON INSULATED TERMINAL GD0801
£1.00

The Makita HM0860C is a heavy-duty SDS-Max demolition hammer designed for demanding chiselling and breaking work. Its impact system contains a substantial number of individual components, including the tool holder, striker, cylinder, piston, connecting rod and crankshaft, while the electric motor uses conventional carbon brushes and separate field and armature components.

If your Makita HM0860C is not working, has lost impact power, is making unusual noises or has developed a problem with the chisel holder or motor, identifying the correct Makita HM0860C spare parts can make a repair much more straightforward.

Makita HM0860C Parts Diagram and Parts List

The HM0860C parts diagram breaks the demolition hammer down into its front tool-holder assembly, impact mechanism, crank housing, motor and electrical sections. The detailed parts list includes individual springs, O-rings, washers, retaining rings and pins alongside larger components.

This is particularly useful for an older demolition hammer where several small parts may need to be replaced during an internal repair. Matching the numbered position with the corresponding part number helps identify the correct component before ordering.

HM0860C SDS-Max Tool Holder Parts

The front tool-retention mechanism is exposed to repeated impact and vibration during chiselling. The parts breakdown includes the 286269-2 tool holder cap, 418351-1 chuck cover, 331659-5 chuck ring, 310108-5 tool retainer, 418357-9 change ring and 324387-9 tool holder.

The assembly also contains steel balls, ring springs, washers, O-rings and other retaining components.

If the HM0860C tool holder is loose, a chisel is not being retained properly or the locking mechanism is difficult to operate, these individual components should be inspected for wear or damage.

HM0860C Barrel, Striker and Impact Parts

The barrel and impact assembly are responsible for transferring the hammering force to the SDS-Max accessory. The parts catalogue identifies the 324389-5 impact bolt, 324388-7 striker, 331658-7 cylinder 32, 418349-8 piston and 418350-3 connecting rod, together with the relevant springs, seals and rings.

If the HM0860C has lost impact power, the piston, striker and cylinder assembly are important areas to investigate. Damaged O-rings or worn internal components can also affect the operation of the impact mechanism.

The 317719-7 cylinder guide and 183719-7 crank housing cover are also separately identified, giving useful options when rebuilding the front and central sections of the hammer.

HM0860C Piston, Crankshaft and Gear Parts

The piston is driven by the crank mechanism, converting the motor's rotation into the reciprocating movement required for the impact system. The parts list includes the 153676-3 crankshaft complete, 418350-3 connecting rod, 418349-8 piston and 153678-9 crank housing complete.

If the Makita HM0860C is making excessive mechanical noise, vibrating abnormally or running without producing the expected hammer action, the crankshaft, connecting rod, bearings and associated drive components should be checked.

The parts catalogue also includes oil seals and several O-rings used throughout this section of the machine.

Makita HM0860C Motor and Carbon Brushes

The HM0860C uses a conventional brushed motor, with separate field, motor housing, brush-holder and carbon-brush components. The parts listings identify 634506-2 field assembly for 110V and 634508-8 field assembly for 240V machines.

The brush section includes the 418362-6 brush holder cover, 643750-0 brush holder cap and carbon-brush options including 191961-6, 193922-2 and 194285-9 depending on the applicable parts version.

If the HM0860C is losing power, sparking excessively, cutting out or refusing to start, the carbon brushes, armature, field and motor bearings should be checked. Make sure motor and electrical components correspond with the voltage of your machine.

HM0860C Switch and Electrical Parts

Electrical components are another area to investigate when a HM0860C will not start. The parts breakdown identifies the 651423-1 switch, 418360-0 switch lever, 418361-8 switch box, motor support and associated electrical fittings.

A faulty switch or damaged connection can prevent the motor from operating even when the mechanical impact assembly is in good condition. The switch and surrounding components should therefore be checked alongside the carbon brushes and motor if the machine has stopped working.

HM0860C Housing, Fan and Small Components

The motor assembly includes a dedicated housing and cooling components, including the 153677-1 motor housing complete, 135058-1 fan assembly and 638293-5 support complete.

The HM0860C also contains a large number of smaller service parts, including springs, retaining rings, flat washers, pins, O-rings and screws. These can become particularly important when servicing the machine after years of heavy use, as a small worn or damaged component can affect a much larger assembly.

Finding the Right Makita HM0860C Parts

When searching for Makita HM0860C parts online, use the complete model number and the part number from the relevant parts list wherever possible. The HM0860C contains many similar-looking internal components, making an exact part-number match especially useful.

From HM0860C SDS-Max tool holder parts and impact components to the barrel, striker, piston, crankshaft, carbon brushes, field, motor housing, switch and electrical components, the detailed parts information makes it easier to identify the individual Makita HM0860C replacement parts required for a repair.

For electrical and motor components in particular, check whether your machine is the 110V or 240V version before ordering.