Skip to main content

Makita HR3000C Parts

CAP HR3000C
£1.00
CHUCK COVER HR3000C
£2.25
COMPRESSION SPRING 38 HR160DW
£1.00
RING SPRING 19 HR160DW/HR2420
£1.00
PIN 8 HR160DW/2410/HR3000C
£2.35
CHUCK RING HR2410/2420/HR3000C
£0.00 Not Available
LEAF SPRING 26 BHR200S/HR2430
£2.15
RING SPRING 30.5 HR3000C/HR200
£1.00
SPRING GUIDE HR2410/2420//HR30
£2.15
*COMPRESSION SPRING 35
£1.00
GUIDE WASHER HR3000C
£1.00
SEAL CASE HR3000C
£1.95
O RING 46 HR3000C
£1.00
OIL SEAL 28 HR3000C/3210FCT
£2.55
RETAINING RING R-52 HM1200K
£2.15
*EXT DIN 471 CIRCLIP-28
£1.00
BALL BEARING 60/28LLU
£7.65
STEEL BALL 7.0 M3601/M8701
£1.00
TOOL HOLDER HR3000C
£30.25
PIN 8 HR3000C
£1.00
FLUORO CARBON RESING RING 20
£7.25
O RING 15 HR3000C
£1.00
IMPACT BOLT HR3000C
£8.85
O RING 15 HR3000C
£1.00
FLUORO CARBON RESING RING 20
£7.25
*RUBBER RING 13 HR3000C
£6.25
RUBBER RING 13 HR3000C
£6.25
SLEEVE 12 HR3000C
£3.65
WASHER 19 HR3000C
£4.55
PIN 2.5 HR3000C/BTW200/6990D
£1.00
*PIN HOLDER HR3000C
£1.00
PIN HOLDER FOR R RING HR3000C
£1.75
STRIKER HR3000C
£4.85
O RING 18 HR3000C
£1.00
CYLINDER HR3000C
£68.75
SLEEVE 50 HR3000C
£8.75
COMPRESSION SPRING 40 HR3000C
£1.85
LOCK SLEEVE HR3000C
£1.85
RING 29 HR3000C
£9.45
COMPRESSION SPRING 34 HR3000C
£2.15
DRIVING SLEEVE HR3000C
£18.25
O RING 26 CC300D/HR3000/BSS50
£1.00
SPIRAL BEVEL GEAR 37 HR3000C
£19.95
O RING 18 HR3000C
£1.00
O RING 18 HR3000C
£1.00
PIN 7 HR3000C
£1.00
PISTON HR3000C
£3.25
ROD HR3000C
£1.00
GRIP SPRING 63 HR3000C/3210FCT
£4.85
CUP SQUARE NECK BOLT M6x80
£2.85
PLATE HR3000C/4000C/5001C/3540
£1.00
HEX FULL NUT M6 LF1000/DST111
£1.00
SIDE GRIP BASE 63 HR3000C
£3.85
WING SCREW M6X14 HS7611
£2.45
*GRIP 36 COMP HR3000/HR4000C
£8.45
PAN HEAD SCREW M4X12 VC3211M
£1.00
CRANK HOUSING COVER COMP HR300
£13.75
DUSTPROOF WASHER HR3000C
£3.35
O RING 20 VC3211M/HR3000C/690
£1.00
CHANGE LEVER COMP HR3000C
£3.05
PIN 4
£1.00
LOCK BUTTON HR3000C
£1.00
COMPRESSION SPRING 2
£1.00
INDICATION LABEL HR3000C/4000C
£1.00
HEX SOCKET FLAT HD SCREW M5
£2.85
O RING 4 BPJ140/180/BURAT1827H
£1.00
SHIFT LEVER COMP HR3000C
£2.85
CRANK HOUSING COMP HR3000C
£48.35
CRANK CAP HR3000C/HR4000C
£1.85
O RING 30 VC3211M/HR5000/HM13
£1.00
PT SCREW 5X30 9015B/UC3530A
£1.00
O RING 10 GN900SE/HR3000C
£1.00
SPUR GEAR 21 COMP HR3000C
£2.55
HANDLE HR3000C
£13.15
SWITCH LEVER HR4000C/HR5001C
£1.75
SWITCH TG71B PC5000/5001C/KP0
£11.15
LEAD GUIDE HR3000C/4000C/4500C
£1.75
SPONGE SHEET HR3000C/4000C/450
£1.00
TAPPING SCREW 4X18
£1.00
HANDLE COVER HR3000C
£14.85
TAPPING SCREW 4X18
£1.00
STRAIN RELIEF 110V UK360/HS61
£1.00
CORD GUARD 10 HM1317C/CB/HR30
£2.25
CORD GUARD 11.5 HM1202C 9069S
£1.75
POWER SUPPLY CORD 1.5-2-4.0
£10.50
*POWER SUPPLY CORD 1.5-2-4.0
£12.05
POWER SUPPLY CORD 1.5-2-4.0
£23.45
PT SCREW 5X20 HM1303
£1.00
ACRYLIC PIN 5 HR4000C/HR3000C
£1.00
PAN HD SCREW M5X20 W/CP WASHE
£1.00
CRANK SHAFT HR3000C
£21.15
KEY 4 HR3000C
£1.75
BALL BEARING 6004LLU HR3000C
£4.55
EXT DIN 471 CIRCLIP-20 VC3211
£1.00
RETAINING RING R-42 HR3000C
£1.85
CONICAL COMP SPRING 21-31 HR30
£1.00
CLUTCH HR3000C
£17.15
HELICAL GEAR HR3000C
£11.25
BLUE WASHER 10 HR3000C
£1.00
EXT DIN 471 CIRCLIP-10 KP0810
£1.00
OIL SEAL 10 HR3000C
£4.25
SLEEVE 10 HR3000C
£4.25
BALL BEARING 6000LU HR3000C
£3.25
100 253171-4
THIN WASHER 10 BST220/HR3000C
£1.00
101 226782-8
SPIRAL BEVEL GEAR 10 HR3000C
£10.15
102 254202-2
KEY 4-10 9401/9900B/9402/LF10
£1.00
103 211138-8
BALL BEARING 6001LLU HR3000C
£3.55
104 151692-9
*TORQUE LIMITER COMP HR3000C
£32.55
104 152955-6
TORQUE LIMITER COMP HR3000C
£44.35
105 961006-2
EXT DIN 471 CIRCLIP-10 KP0810
£1.00
106 210024-0
BALL BEARING 608 2RS HR5001C
£2.85
107 253314-8
THIN WASHER 15 HR3000C/DTD154
£1.00
108 421702-9
SEAL RING HR3000C
£1.85
109 151695-3
GEAR HOUSING COMP HR3000C
£21.15
110 417010-4
BAFFLE PLATE HR3000C
£2.15
111 634345-0
FIELD 110V HR3000C
£10.65 Not Available
111 634348-4
FIELD 240V HR3000C
£12.65
112 266046-8
PT SCREW 5X50 HR2000
£1.00
113 632933-7
SUPPORT COMP HR3000C
£3.95
114 513516-1
ARMATURE 110V HR3000C
£53.45
114 513518-7
ARMATURE 240V HR3000C
£53.45
114 516381-7
*ARMATURE 110V HR3000C
£53.45
114 516383-3
*ARMATURE 240V HR3000C
£49.45
115 681650-6
INSULATION WASHER HM0870/71C
£4.95
116 210005-4
BALL BEARING 608DDW GA5020
£6.15
117 151840-0
MOTOR HOUSING COMP HR3000C
£28.55
118 851772-8
NAME PLATE HR3000C
£1.00
119 191961-6
*AC CARBON BRUSH CB-304 HM1100
£9.15
119 193922-2
*AC CARBON BRUSH CB-323
£9.15
119 194285-9
AC CARBON BRUSH CB-327 (Pair)
£9.15
120 643750-0
BRUSH HOLDER CAP 4100KB HS7611
£1.00
121 263002-9
RUBBER PIN 4 GA7050/9050/5021
£1.00
122 417024-3
BRUSH HOLDER COVER HR3000C
£1.00
123 265995-6
TAPPING SCREW 4X18
£1.00
124 323937-7
*SHOULDER SLEEVE 7 HR3000C
£2.05
124 324261-1
SHOULDER SLEEVE 7 HR3000C
£2.15
125 241863-7
FAN HR3000C/JR3060T/3070/3540
£2.15
126 253047-5
WASHER 6 HR3000C/LF1000
£1.00
126 941151-9
FLAT WASHER 6 DIN125-B BHS630
£1.00
127 931302-2
HEX FULL NUT M6 LF1000/DST111
£1.00
127 252153-3
HEX NUT M6-10 L.THR 9911
£1.00
128 417012-0
REAR COVER HR3000C
£4.35
129 265995-6
TAPPING SCREW 4X18
£1.00
130 417017-0
FIX ROD HR3000C
£1.00
131 631367-1
*CONTROLLER HR3000C 110V
£47.15
131 631368-9
CONTROLLER HR3000C 110V
£37.55
131 631369-7
CONTROLLER HR3000C 240V
£49.95
132 267088-5
HARD WASHER 28 6904VH
£1.85
133 262088-0
URETHANE RING 28 HR3000C
£2.45
134 253133-2
WASHER 7 HR160D/DA4000LR
£1.00
1001 194683-7
Grease vessel set, 100 ml
£7.60
1001 181573-3
GREASE VESSEL 93G
£5.24
1002 321248-4
DEPTH GAUGE
£5.70
1003 824559-1
PLASTIC CARRYING CASE
£59.62
2001 134889-5
GRIP ASSY 36 HR3000C
£18.20
5001 819001-5
LABEL/MAKITA
£1.00
5002 654091-9
NON INSULATED TERMINAL GD0801
£1.00
5003 655030-2
PLUG UK TYPE 16A-4H/110V
£8.34
5004 645200-1
NOISE SUPPRESSOR
£3.05
5005 685722-9
SPONGE
£1.00

The Makita HR3000C is a heavy-duty 30mm SDS-Plus rotary hammer designed for drilling, hammer drilling and chiselling. Its impact mechanism, substantial front tool holder and powerful motor make it suitable for demanding work, but the combination of impact, vibration and regular use can eventually lead to wear in the mechanical and electrical components.

If your Makita HR3000C is not working, has lost impact power, is struggling to hold an SDS-Plus bit, making unusual noises or has developed an electrical fault, the individual HR3000C spare parts can be identified from the parts diagram and list above.

Makita HR3000C Parts Diagram and Parts List

The HR3000C parts diagram breaks the rotary hammer down into the front tool holder, impact mechanism, gear assembly, crank mechanism, motor and electrical sections. This is particularly useful on an older rotary hammer where a fault may involve a relatively small spring, seal, bearing or retaining component.

The parts list includes the tool holder, impact bolt, O-rings, oil seals, driving sleeve, gears, bearings, crank components, handle, switch, controller, armature, field, carbon brushes and power cord.

There are also numerous washers, retaining rings, springs and screws listed individually, allowing specific components to be identified without relying solely on complete assemblies.

HR3000C SDS-Plus Tool Holder Parts

The front tool holder is subjected to repeated impact every time the HR3000C is used with a drill bit or chisel. The parts breakdown identifies 323912-3 tool holder, 323913-1 impact bolt, 286253-7 cap 40, 417027-7 chuck cover and 216022-2 steel ball 7mm.

If the HR3000C is not holding bits securely, the tool holder, steel ball, springs, pins and retaining components should be inspected. Excessive movement at the bit end can indicate wear in the tool-retention mechanism.

The front assembly also contains several O-rings, resin rings, washers and seals. These components are important to the movement and sealing of the impact mechanism.

HR3000C Impact Mechanism and Piston Parts

The impact mechanism converts the motor's rotation into the reciprocating action required for hammer drilling and chiselling. The parts catalogue includes the 331558-1 driving sleeve, impact components, compression springs, O-rings and associated internal parts.

If the HR3000C has lost impact power, the impact mechanism is one of the main areas worth investigating. Worn seals or damaged internal components can affect the efficiency of the hammer action even when the motor itself is still running.

The parts breakdown also contains numerous individual sealing components, including 213615-6 O-ring 46, 213436-6 oil seal 28, 213321-3 fluoro carbon resin ring and 213228-3 O-ring 15.

HR3000C Gears, Bearings and Crank Components

The motor drives the mechanical assemblies through a series of gears and bearings. The HR3000C parts information includes 226783-6 spiral bevel gear 37, 151758-5 spur gear 21 complete and 211422-1 ball bearing 60/28LLU.

If the HR3000C is making grinding or unusual mechanical noises, loses drive or develops excessive vibration, the gears, bearings and crank mechanism should be inspected. Wear in these components can become more noticeable when the tool is used continuously for drilling or chiselling.

Individual bearings, washers, retaining rings and other supporting parts are also identified within the parts list.

HR3000C Motor, Armature and Carbon Brushes

The HR3000C uses a conventional brushed motor, with replaceable carbon brushes and separate armature and field components. The parts breakdown identifies 191961-6 AC carbon brush, 643750-0 brush holder cap and 417024-3 brush holder cover.

If your HR3000C is losing power, producing excessive sparking or cutting out during use, the carbon brushes and brush holder should be inspected. The armature and field can also be checked if the motor continues to show problems after the brushes have been inspected.

The motor section includes 151840-0 motor housing complete, together with the relevant armature, field and bearing components.

HR3000C Controller, Switch and Electrical Parts

The HR3000C includes electronic control components as well as the conventional motor parts. The parts catalogue identifies 631368-9 controller for 110V and 631369-7 controller for 240V, with an additional 110V controller reference 631367-1 appearing in the parts information.

The 651922-3 switch and 416284-4 switch lever are also included in the electrical and control section.

If the Makita HR3000C will not start, check the power supply, switch, cable, controller, carbon brushes and motor connections. Always match electrical replacement parts to the voltage of the machine, particularly when working with the 110V and 240V versions.

HR3000C Power Cord, Handle and Housing Parts

The rear of the HR3000C contains the handle, electrical connections and cable-entry components. The parts breakdown includes the 417014-6 handle, 417012-0 rear cover, 687169-3 strain relief, 682560-0 cord guard and associated screws and fixings.

If the HR3000C power cord is damaged, the cable-entry area should also be checked for damage to the cord guard or strain relief. A damaged handle or rear housing component can likewise be replaced individually where listed.

The 417017-0 fix rod and various small fasteners form part of the rear assembly.

HR3000C Seals, Springs and Small Parts

The HR3000C contains a large number of small components within its impact and tool-holder assemblies. Springs, pins, retaining rings, washers and seals can all be important when rebuilding the front mechanism.

Examples include 231936-4 ring spring 30.5, 323819-3 spring guide, 233234-2 compression spring 35, 256447-8 pin 8 and 344841-7 guide washer.

These smaller HR3000C parts are particularly useful when servicing an older machine that has been dismantled or where a particular component has become worn or damaged.

Identifying the Correct Makita HR3000C Parts

When searching for Makita HR3000C parts online, check the exact model and voltage before ordering, particularly for electrical components. The parts information contains separate references for 110V and 240V controllers and other electrical components.

From the HR3000C SDS-Plus tool holder and impact mechanism to the driving sleeve, gears, bearings, armature, field, carbon brushes, controller, switch, handle and power cord, the detailed parts list provides a useful reference for identifying individual components.

Matching the original Makita part number with the HR3000C parts diagram is the best way to select the correct HR3000C spare parts for your rotary hammer.