3 6010A 011 Spares and Parts for BOSCH ROUTER PR 10 E (ROUTERS)

Ref:	Part Number:	Description	Price
1	2 609 100 200	Motor Housing	£9.05
4	2 609 120 274	Switch	£9.45
5	1 604 460 308	Power Supply Cord	£8.02
6	2 600 703 018	Grommet	£2.33
7	2 601 035 001	Cable Clip	£1.00
9	2 609 130 778	Warning Plate	£1.67
11	2 609 130 777	Warning Plate	£2.05
12	1 607 233 189	Regulator	£19.05
13	2 609 110 435	Deep-groove Ball Bearing	£5.30
14	2 609 110 436	Deep-groove Ball Bearing	£4.78
15	2 609 110 253	Self-locking Nut	£2.45
16	2 609 110 217	Brush Holder	£1.00
17	2 609 100 203	Brush-cover	£1.00
18	2 609 110 294	Spring Washer	£1.00
19	2 910 611 093	Tapping Screw	£1.00
20	2 609 110 490	Tapping Screw	£1.00
23	2 910 611 020	Tapping Screw	£1.00
24	2 916 650 006	Spring Retaining clip DIN 471-15X1-FST	£1.00
37	2 603 490 017	Torx Oval-head Screw	£1.00
40	2 609 100 247	Air-deflector Ring	£2.33
41	2 609 120 153	Terminal	£1.00
42	2 609 110 297	Contact Strap	£1.00
43	2 609 120 173	End Cap	£1.00
52	2 609 110 245	Pressure Spindle	£1.00
53	2 609 110 246	Spring Plate	£1.00
60	2 609 100 420	Housing Cover	£6.12
61	2 609 130 914	Manufacturer's Nameplate	£2.51
90	2 609 110 741	Plate	£2.45
91	2 609 100 248	Button	£1.00
92	2 609 110 255	Compression Spring	£1.00
93	2 609 110 480	Cover Plate	£1.00
94	2 609 110 367	Screw	£1.00
659	2 609 100 568	Knurled Thumbscrew	£2.45
662	2 916 011 014	Plain Washer	£1.00
698	2 609 110 786	Single-head Eng. Wrench	£5.30
698	2 609 110 438	Single-head Eng. Wrench	£4.19
802	2 610 008 119	Stator	£37.23
803	2 610 008 120	Armature	£50.31
808	2 610 007 798	Nameplate	£1.90
810	2 610 008 121	Carbon-brush Set	£8.73
830	2 610 008 122	Collet	£7.76
850	2 610 008 123	Bearing Flange	£25.04
854	2 609 100 387	Base Plate	£7.76
854	2 609 110 378	Shaft	£8.73
854	2 609 110 379	Toothed Belt Wheel	£3.03
854	2 609 110 380	Toothed Belt Wheel	£4.01
854	2 609 170 038	V-belt	£6.12
854	2 609 100 386	Cover	£6.12
854	2 609 110 381	Spring	£1.00
854	2 609 110 382	Button	£1.00
854	2 910 861 126	Countersunk-head Screw	£1.00
854	2 609 170 047	Cover	£1.00
854	2 609 110 606	Ball Bearing	£7.76
854	2 609 110 462	Spring Retaining Ring	£4.02
854	2 609 100 389	Cover	£5.30
854	2 609 110 505	Nut	£2.05
854	2 609 110 557	Protection Plate	£3.35
854	2 610 008 114	Base	£118.31
854	2 609 199 041	Clamping Lever	£4.01
854	2 609 110 289	Hex Nut	£1.00
854	2 609 110 282	Conical Spring Washer	£1.00
854	2 609 110 290	Washer	£1.00
855	2 609 110 372	Base Plate	£4.19
855	2 609 100 381	Base	£4.78
855	2 609 110 455	Pin	£1.00
855	2 609 199 008	Wing Nut	£1.00
855	2 609 110 483	Pin	£1.00
855	2 609 110 347	Screw	£1.00
855	2 610 008 115	Base	£63.47
855	2 600 590 006	Ratchet Cap	£1.00
855	2 916 011 014	Plain Washer	£1.00
855	2 910 281 201	Round-head Bolt	£1.00
855	2 609 199 041	Clamping Lever	£4.01
855	2 609 110 289	Hex Nut	£1.00
855	2 609 110 282	Conical Spring Washer	£1.00
855	2 609 110 290	Washer	£1.00
855	2 609 110 241	Screw	£3.03
855	2 609 110 306	Compression Spring	£1.00
856	2 609 110 457	Adjusting Cam	£1.00
856	2 609 110 458	Screw	£1.00
856	2 609 110 459	Adjusting Wrench	£2.05
856	2 609 110 279	Hexagon-socket Key	£1.67
856	2 610 008 116	Base	£17.37
857	2 609 199 008	Wing Nut	£1.00
857	2 609 110 364	Screw	£1.00
857	2 610 008 113	Edge Guide	£15.05
858	2 610 008 117	Edge Guide	£33.34
859	2 609 199 063	Edge Guide	£7.01
860	2 609 110 307	Base Plate	£21.65
860	2 610 008 124	Base Plate	£7.76
860	2 610 008 111	Base	£41.02
860	2 609 199 041	Clamping Lever	£4.01
860	2 609 110 289	Hex Nut	£1.00
860	2 609 110 282	Conical Spring Washer	£1.00
860	2 609 110 290	Washer	£1.00
860	2 609 110 241	Screw	£3.03
860	2 609 110 306	Compression Spring	£1.00
860	2 609 110 283	Bolt	£2.05
864	2 609 100 383	Base Plate	£15.05
864	2 609 100 423	Handle	£3.03
864	2 609 100 140	Cap-handle	£4.01
864	2 609 110 607	Screw	£2.05
864	2 609 110 548	Nut	£1.00
865	2 609 199 114	Knurled Thumbscrew	£6.12
866	2 609 199 100	Screw	£1.00
868	2 609 110 553	Screw	£1.00
869	2 610 907 746	Adapter	£5.30
870	2 609 100 384	Dust Chamber	£5.30
871	2 609 100 385	Chute	£6.12

Accessories for Bosch 3 6010A 011

Two flute cutter 3mm diameter - C001AX1/4TC

Solid carbide two flute cutter. 3.0mm diameter X 9.5mm cut for softwood, harwood, MDF, plywood and chipboard.

D=3 mm Cut length=3/8 inch Cut length=9.5 mm Shank Diameter=1/4 inch Includes:

Price: £10.50

Two flute cutter 3.2mm diameter - C001BX1/4TC

Solid carbide two flute cutter. 3.2mm diameter X 12.7mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/8 inch D=3.2 mm Cut length=1/2 inch Cut length=12.7 mm Shank Diameter=1/4 inch Includes:

Price: £13.73

Two flute cutter 6.3mm diameter - C007X1/4TC

Two flute cutter 6.3mm diameter X 19.1mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/4 inch D=6.3 mm Cut length=3/4 inch Cut length=19.1 mm Shank Diameter=1/4 inch Includes:

Price: £8.82

Two flute cutter 6.3mm diameter - C008X1/4TC

Two flute cutter 6.3mm diameter X 25.4mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/4 inch D=6.3 mm Cut length=1 inch Cut length=25.4 mm Overall length=68.5 mm Shank Diameter=1/4 inch Includes:

Price: £11.00

Two flute cutter 8.0mm diameter - C012AX1/4TC

Two flute cutter 8.0mm diameter X 25.0mm cut for softwood, harwood, MDF, plywood and chipboard.

D=8 mm Cut length=25 mm Shank Diameter=1/4 inch Includes:

Price: £11.00

Two flute cutter 10mm diameter - C016X1/4TC

Two flute cutter 10mm diameter X 19.1mm cut for softwood, harwood, MDF, plywood and chipboard.

D=25/64 inch D=10 mm Cut length=3/4 inch Cut length=19.1 mm Shank Diameter=1/4 inch Includes:

Price: £13.01

Two flute cutter 12mm diameter - C019AX1/4TC

Microgranular tungsten tipped two flute Cutter 12.0mm diameter X 19.0mm cut for a perfect finish for softwood, harwood, MDF, plywood and chipboard.

D=15/32 inch D=12 mm C=19 mm C=3/4 inch Shank Diameter=1/4 inch Includes:

Price: £16.57

Two flute cutter 12mm diameter - C019X1/4TC

Two flute cutter 12mm diameter X 19.1mm cut for softwood, harwood, MDF, plywood and chipboard.

D=15/32 inch D=12 mm Cut length=3/4 inch Cut length=19.1 mm Shank Diameter=1/4 inch Includes:

Price: £12.69

Two flute cutter 12.7mm diameter - C022X1/4TC

Two flute cutter 12.7mm diameter X 31.8mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/2 inch D=12.7 mm Cut length=1 1/4 inch Cut length=31.8 mm Shank Diameter=1/4 inch Includes:

Price: £14.90

Two flute cutter 15.0mm diameter - C024AX1/4TC

Two flute cutter 15.0mm diameter X 25mm cut for softwood, harwood, MDF, plywood and chipboard.

D=19/32 inch D=15 mm Cut length=63/64 inch Cut length=25 mm Shank Diameter=1/4 inch Includes:

Price: £14.06

Two flute cutter 20.0mm diameter - C030AX1/4TC

Two flute cutter 20.0mm diameter X 20mm cut for softwood, harwood, MDF, plywood and chipboard.

D=20 mm Cut length=20 mm Shank Diameter=1/4 inch Includes:

Price: £14.90

Dovetail cutter angle=104 degrees 12.7mm diameter - C041AX1/4TC

TCT dovetail cutter, 104 degrees X 12.7mm diameter X 12.7mm cut for timber, plywood, MDF, chipboard and abrasive plastics.

D=1/2 inch D=12.7 mm Cut length=1/2 inch Cut length=12.7 mm Overall length=61 mm A=104 degrees Shank Diameter=1/4 inch Includes:

Price: £14.90

Self guided chamfer angle=45 degrees x 12.7mm Cut - C049X1/4TC

Self guided chamfer cutter for straight and shaped material. Angle 45 degrees X 32.0mm diameter X 12.7mm cut. Does not require a side fence, supplied with two bearings

D=32 mm C=1/2 inch C=12.7 mm B=9.5 mm A=45 degrees Shank Diameter=1/4 inch Includes:

Price: £23.19

Rounding over 6.3mm radius x 12.7mm cut - C076X1/4TC

Self guided rounding over cutter with 6.3mm radius X 25.4mm diameter X 12.7mm cut. Does not require a side fence, supplied with two bearings.

D=1 inch D=25.4 mm C=1/2 inch C=12.7 mm B=9.5 mm B2=12.7 mm R=6.3 mm R=1/4 inch Shank Diameter=1/4 inch Includes:

Price: £27.60

Rounding over 9.5mm radius x 15.9mm cut - C078X1/4TC

Self guided rounding over cutter with 9.5mm radius X 31.7mm diameter X 15.9mm cut.

D=31.7 mm Cut length=5/8 inch Cut length=15.9 mm B=9.5 mm B2=12.7 mm R=9.5 mm Shank Diameter=1/4 inch Includes:

Price: £32.01

Self guided trimmer 12.7mm diameter - C116X1/4TC

Self guided trimmer 12.7mm diameter X 25.4mm cut for trimming plastic or plywood overlays.

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm B=12.7 mm A=90 degrees Shank Diameter=1/4 inch Includes:

Price: £16.15

Template profile 12.7mm diameter - C121X1/4TC

Bearing guided template profile for rebating and trimming only. 12.7mm diameter X 25.4mm cut.

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Shank Diameter=1/4 inch Includes:

Price: £17.09

Biscuit jointer set - C152X1/4TC

Two wing self-guiding TCT cutter ideal for biscuit jointing, 37.2mm diameter X 4.0mm cut. Three ball bearings supplied (12.7mm, 16.0mm and 19.0mm)

D=37.2 mm Cut length=4 mm B=12.7 mm B2=16.0 mm B3=19.0 mm Shank Diameter=1/4 inch Includes:

Price: £33.60

Guided trimmer 6.35mm diameter x 25.4mm - C168X1/4TC

Guided trimmer 6.35mm diameter X 25.4mm cut for trimming pastic or plywood overlays.

D=1/4 inch D=6.35 mm Cut length=1 inch Cut length=25.4 mm B=6.35 mm A=90 degrees Shank Diameter=1/4 inch Includes:

Price: £13.73

Intumescent cutter set 10mm x 24mm - C209X1/4TC

Neat cut intumescent cutter set, 24mm diameter X 10mm cut for grooves on door frames for intumescent strips.

D=24 mm C=10 mm B=16 mm E=4 mm Shank Diameter=1/4 inch Includes:

Price: £26.44

Intumescent cutter set 15mm x 24mm - C220X1/4TC

Neat cut intumescent cutter set, 24mm diameter X 15mm cut for grooves on door frames for intumescent strips.

D=24 mm C=15 mm B=16 mm E=4 mm Shank Diameter=1/4 inch Includes:

Price: £27.71

Two flute cutter 15.9mm diameter - TR19X1/4TC

Two flute cutter for a clean finish. 15.9mm diameter X 19.0mm cut.

D=5/8 inch D=15.9 mm C=19 mm OL=60 mm Shank Diameter=1/4 inch Includes:

Price: £21.51

Two flute cutter 19.1mm diameter - TR20X1/4TC

Two flute cutter for a clean finish. 19.1mm diameter X 25.0mm cut.

D=3/4 inch D=19.1 mm C=25 mm OL=65.5 mm Shank Diameter=1/4 inch Includes:

Price: £21.51

Radius 5mm radius and 18mm diameter - TR21X1/4TC

Radius cutter for edge coves and fluting. 5.0mm radius X 18.0mm cut.

Cut length=18 mm R=5 mm Shank Diameter=1/4 inch Includes:

Price: £20.97

Chamfer V groove cutter angle=45 degrees - TR22X1/4TC

Chamfer and V groove cutter, ideal for fast chamfering to remove edge on timber, or creating a decorative edge. 45 degrees X 12.7mm diameter.

D=1/2 inch D=12.7 mm Overall length=53 mm A=45 degrees Shank Diameter=1/4 inch Includes:

Price: £17.63

Guided trimmer 6.35mm x 12.7 - TR23X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 6.35mm diameter X 12.7mm cut

D=1/4 inch D=6.35 mm Cut length=1/2 inch Cut length=12.7 mm Shank Diameter=1/4 inch Includes:

Price: £15.95

Guided trimmer 6.3mm diameter x 25.4 - TR24X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 6.35mm diameter X 25.4mm cut

D=1/4 inch D=6.35 mm Cut length=1 inch Cut length=25.4 mm Overall length=74.2 mm Shank Diameter=1/4 inch Includes:

Price: £16.57

Guided trimmer 9.5mm diameter x 12.7 - TR25X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 9.5mm diameter X 12.7mm cut

D=3/8 inch D=9.5 mm Cut length=1/2 inch Cut length=12.7 mm Overall length=63 mm Shank Diameter=1/4 inch Includes:

Price: £19.31

Guided trimmer 12.7mm diameter x 25.4 - TR26X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 12.7mm diameter X 25.4mm cut

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Overall length=76.5 mm Shank Diameter=1/4 inch Includes:

Price: £21.51

Guided trimmer triple fluted 12.7X25.4 - TR27X1/4TC

Triple flutted bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 12.7mm diameter X 25.4mm cut

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Shank Diameter=1/4 inch Includes:

Price: £26.44

Guided trimmer 12.7mm x50mm - TR28X1/2TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 12.7mm diameter X 50.0mm cut

D=1/2 inch D=12.7 mm Cut length=50 mm Shank Diameter=1/4 inch Includes:

Price: £38.02

Guided profiler - TR29X1/4TC

Guided profiler for trimming and profiling timber and man made board. 12.7mm diameter X 25.4mm cut.

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Overall length=70.8 mm Shank Diameter=1/4 inch Includes:

Price: £23.19

Guided profiler - TR30X1/2TC

Guided profiler for trimming and profiling timber and man made board. 19.1mm diameter X 50.0mm cut.

D=3/4 inch D=19.1 mm Cut length=50 mm Overall length=95 mm Shank Diameter=1/2 inch Includes:

Price: £43.05

Guided ovolo round over cutter 6.35mm radius - TR31X1/4TC

Bearing guided ovolo cutter, produces a smooth round over profile. 25.4mm diameter, incudes 12.7mm bearing.

D=1 inch D=25.4 mm B=9.5 mm R=6.3 mm Shank Diameter=1/4 inch Includes:

Price: £36.95

Guided ovolo over 9.5mm radius - TR32X1/4TC

Bearing guided ovolo cutter, produces a smooth round over profile. 31.7mm diameter, incudes 12.7mm bearing.

D=31.7 mm B=9.5 mm R=9.5 mm Shank Diameter=1/4 inch Includes:

Price: £39.17

Guided chamfer angle=45 degrees x 31.8mm - TR33X1/4TC

Bearing guided chamfer and V groove cutter, ideal for fast chamfering to remove edge on timber, or creating a decorative edge. 45 degrees X 31.8mm diameter.

D=1 1/4 inches D=31.8 mm Overall length=62 mm B=9.5 mm A=45 degrees Shank Diameter=1/4 inch Includes:

Price: £28.36

Biscuit jointer set - TR35X1/4TC

Bearing guided biscuit jointer set. Enables biscuit jointing with timber, man made fibre and partical board. 37.2mm diameter X 4.0mm cut

D=29/64 inch D=37.2 mm Cut length=4 mm B=12.7 mm Shank Diameter=1/4 inch Includes:

Price: £42.41

Two flute cutter 15mm diameter - TR40DX1/4TC

Two flute cutter for a clean finish, TCT centre tip for drilling abrasive material. 15.0mm diameter X 25.0mm cut.

D=15 mm C=25 mm Shank Diameter=1/4 inch Includes:

Price: £22.56

Router Cutter - C121BX1/4TC

Bearing guided template profile for rebating and trimming only. 12.7mm diameter X 9.5mm cut.

Price: £17.30

Buy Replacement Parts and Accessories for the Bosch 3 6010A 011

Accessories for Bosch 3 6010A 011

Contact Info

Secure Shopping

Our Service

Help And Advice

Your Account

Recently Viewed