3 60117 800 Spares and Parts for BOSCH ROUTER GMF 1400 CE (ROUTERS)

Ref:	Part Number:	Description	Price
1	2 610 922 584	Motor Housing	£27.69
2	2 610 941 203	Field	£50.31
3	2 610 941 202	Armature	£162.89	NOT AVAILABLE
4	2 610 936 579	Switch Rocker	£6.56	NOT AVAILABLE
5	2 610 935 598	Power Supply Cord	£16.29
6	3 600 703 508	Grommet	£2.33
7	2 601 035 001	Cable Clip	£1.00
8	2 610 935 599	Nameplate	£2.39
9	2 610 935 603	Label	£2.39	NOT AVAILABLE
12	2 610 938 252	Suppression Capacitor	£4.02	NOT AVAILABLE
13	3 600 905 513	Deep-groove Ball Bearing	£8.73
14	3 600 905 512	Deep-groove Ball Bearing	£4.05
21	2 610 991 373	Insulating Sleeve	£7.76
22	1 604 477 005	Blade Terminal	£2.33
29	2 610 993 582	Nut	£3.60
31	2 610 941 007	Rear Housing Section	£7.76
32	2 610 991 375	Bearing Holder	£4.19
33	1 900 210 115	O-ring	£2.33
34	2 610 941 008	Set Of Handles	£6.12
35	1 607 233 135	Speed Governor	£30.51
39	2 610 991 387	Handle	£8.73
40	2 610 925 365	Base	£55.92
44	2 610 922 527	Rod	£3.03
45	2 610 991 385	Lever	£4.01
46	2 610 991 371	Spring	£2.05
48	2 610 993 576	Adjusting Device	£2.33
49	2 610 993 577	Ring	£1.00
50	2 610 928 164	Cover Plate	£11.37	NOT AVAILABLE
55	2 610 991 389	Chip Deflector	£4.02	NOT AVAILABLE
56	2 610 991 372	Cover	£1.00
61	2 910 611 006	Tapping Screw	£2.29
62	2 610 991 306	Tapping Screw	£1.00
63	2 910 011 219	Socket Head Cap Screw	£1.00
70	2 610 996 054	Retaining Snap Ring	£1.00
74	2 910 641 120	Oval-head Screw	£1.00
75	2 610 910 566	Tapping Screw	£1.00
76	2 916 011 013	Plain Washer	£1.00
77	2 910 141 166	Hex Socket Head Cap Screw	£1.00
109	2 610 935 604	Label	£2.51
110	2 610 912 594	Protection Cover	£2.05
111	2 610 990 022	Screw	£1.00
112	2 610 914 852	Plug	£1.00	NOT AVAILABLE
116	2 916 079 032	Serrated Lock-washer	£1.00
117	2 610 994 492	Bolt	£1.00
118	2 610 996 143	Screw	£1.00
119	2 610 913 441	Screw	£1.00
120	2 610 912 597	Handle	£11.64
121	2 610 996 107	Handle	£13.34
122	2 610 914 639	Disc	£1.00	NOT AVAILABLE
123	2 610 912 598	Compression Spring	£1.00
124	3 605 510 548	Bellows	£4.19
125	2 610 915 161	Screw	£2.33	NOT AVAILABLE
127	2 610 997 099	Cover Plate	£15.05
130	2 916 650 003	Spring Retaining Ring	£1.00
131	1 900 210 111	O-ring	£1.00
144	3 603 450 504	Lock Bolt	£4.01
145	3 604 651 503	Compression Spring	£2.05
146	3 602 000 510	Locking Lever	£2.33
147	2 910 641 122	Oval-head Screw	£2.05
148	2 916 680 005	Spring Lock Washer	£1.00
150	2 610 992 417	Single-head Eng. Wrench	£11.64
151	2 610 991 388	Single-head Eng. Wrench	£5.91	NOT AVAILABLE
155	2 610 912 599	Chip Deflector	£4.43	NOT AVAILABLE
156	2 610 935 605	Label	£2.51
157	2 610 997 094	Pointer	£4.19
158	2 610 912 600	Rod	£6.12
159	1 613 480 008	Wing Screw	£1.00
160	2 610 912 601	Knob	£0.00	NOT AVAILABLE
161	2 610 068 154	O-ring	£0.00	NOT AVAILABLE
170	3 600 232 503	Depth-gauge	£7.37
171	2 600 590 006	Ratchet Cap	£1.00
172	3 603 415 556	Pan Head Screw	£2.05
173	3 916 060 500	Spring Washer	£1.00
183	2 918 660 004	Washer	£1.00
184	1 613 300 006	Hex Nut	£1.00
186	2 610 915 060	Clamping Lever	£1.00	NOT AVAILABLE
653	2 610 991 370	Guide Sleeve	£25.04
737	2 608 570 107	Collet	£41.72
737	2 608 570 106	Collet	£0.00	Contact Us
737	2 608 570 105	Collet	£0.00	Contact Us
737	2 608 570 104	Collet	£26.10
737	2 608 570 103	Collet	£0.00	Contact Us
737	2 608 570 108	Collet Chuck	£32.57
801	2 610 924 454	Base	£63.47
810	3 604 321 514	Carbon-brush Set	£6.56
816	3 604 336 506	Brush Holder	£11.37	NOT AVAILABLE
817	3 604 652 501	Spiral Spring	£3.03
826	2 610 997 115	Base	£54.17	NOT AVAILABLE

Accessories for Bosch 3 60117 800

Two flute cutter 3mm diameter - C001AX1/4TC

Solid carbide two flute cutter. 3.0mm diameter X 9.5mm cut for softwood, harwood, MDF, plywood and chipboard.

D=3 mm Cut length=3/8 inch Cut length=9.5 mm Shank Diameter=1/4 inch Includes:

Price: £10.50

Two flute cutter 3.2mm diameter - C001BX1/4TC

Solid carbide two flute cutter. 3.2mm diameter X 12.7mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/8 inch D=3.2 mm Cut length=1/2 inch Cut length=12.7 mm Shank Diameter=1/4 inch Includes:

Price: £13.73

Two flute cutter 6.3mm diameter - C007X1/4TC

Two flute cutter 6.3mm diameter X 19.1mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/4 inch D=6.3 mm Cut length=3/4 inch Cut length=19.1 mm Shank Diameter=1/4 inch Includes:

Price: £8.82

Two flute cutter 6.3mm diameter - C008X1/4TC

Two flute cutter 6.3mm diameter X 25.4mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/4 inch D=6.3 mm Cut length=1 inch Cut length=25.4 mm Overall length=68.5 mm Shank Diameter=1/4 inch Includes:

Price: £11.00

Two flute cutter 8.0mm diameter - C012AX1/4TC

Two flute cutter 8.0mm diameter X 25.0mm cut for softwood, harwood, MDF, plywood and chipboard.

D=8 mm Cut length=25 mm Shank Diameter=1/4 inch Includes:

Price: £11.00

Two flute cutter 10mm diameter - C016X1/4TC

Two flute cutter 10mm diameter X 19.1mm cut for softwood, harwood, MDF, plywood and chipboard.

D=25/64 inch D=10 mm Cut length=3/4 inch Cut length=19.1 mm Shank Diameter=1/4 inch Includes:

Price: £13.01

Two flute cutter 12mm diameter - C019AX1/4TC

Microgranular tungsten tipped two flute Cutter 12.0mm diameter X 19.0mm cut for a perfect finish for softwood, harwood, MDF, plywood and chipboard.

D=15/32 inch D=12 mm C=19 mm C=3/4 inch Shank Diameter=1/4 inch Includes:

Price: £16.57

Two flute cutter 12mm diameter - C019X1/4TC

Two flute cutter 12mm diameter X 19.1mm cut for softwood, harwood, MDF, plywood and chipboard.

D=15/32 inch D=12 mm Cut length=3/4 inch Cut length=19.1 mm Shank Diameter=1/4 inch Includes:

Price: £12.69

Two flute cutter 12.7mm diameter - C022X1/4TC

Two flute cutter 12.7mm diameter X 31.8mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/2 inch D=12.7 mm Cut length=1 1/4 inch Cut length=31.8 mm Shank Diameter=1/4 inch Includes:

Price: £14.90

Two flute cutter 15.0mm diameter - C024AX1/4TC

Two flute cutter 15.0mm diameter X 25mm cut for softwood, harwood, MDF, plywood and chipboard.

D=19/32 inch D=15 mm Cut length=63/64 inch Cut length=25 mm Shank Diameter=1/4 inch Includes:

Price: £14.06

Two flute cutter 20.0mm diameter - C030AX1/4TC

Two flute cutter 20.0mm diameter X 20mm cut for softwood, harwood, MDF, plywood and chipboard.

D=20 mm Cut length=20 mm Shank Diameter=1/4 inch Includes:

Price: £14.90

Dovetail cutter angle=104 degrees 12.7mm diameter - C041AX1/4TC

TCT dovetail cutter, 104 degrees X 12.7mm diameter X 12.7mm cut for timber, plywood, MDF, chipboard and abrasive plastics.

D=1/2 inch D=12.7 mm Cut length=1/2 inch Cut length=12.7 mm Overall length=61 mm A=104 degrees Shank Diameter=1/4 inch Includes:

Price: £14.90

Self guided chamfer angle=45 degrees x 12.7mm Cut - C049X1/4TC

Self guided chamfer cutter for straight and shaped material. Angle 45 degrees X 32.0mm diameter X 12.7mm cut. Does not require a side fence, supplied with two bearings

D=32 mm C=1/2 inch C=12.7 mm B=9.5 mm A=45 degrees Shank Diameter=1/4 inch Includes:

Price: £23.19

Rounding over 6.3mm radius x 12.7mm cut - C076X1/4TC

Self guided rounding over cutter with 6.3mm radius X 25.4mm diameter X 12.7mm cut. Does not require a side fence, supplied with two bearings.

D=1 inch D=25.4 mm C=1/2 inch C=12.7 mm B=9.5 mm B2=12.7 mm R=6.3 mm R=1/4 inch Shank Diameter=1/4 inch Includes:

Price: £27.60

Rounding over 9.5mm radius x 15.9mm cut - C078X1/4TC

Self guided rounding over cutter with 9.5mm radius X 31.7mm diameter X 15.9mm cut.

D=31.7 mm Cut length=5/8 inch Cut length=15.9 mm B=9.5 mm B2=12.7 mm R=9.5 mm Shank Diameter=1/4 inch Includes:

Price: £32.01

Self guided trimmer 12.7mm diameter - C116X1/4TC

Self guided trimmer 12.7mm diameter X 25.4mm cut for trimming plastic or plywood overlays.

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm B=12.7 mm A=90 degrees Shank Diameter=1/4 inch Includes:

Price: £16.15

Template profile 12.7mm diameter - C121X1/4TC

Bearing guided template profile for rebating and trimming only. 12.7mm diameter X 25.4mm cut.

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Shank Diameter=1/4 inch Includes:

Price: £17.09

Biscuit jointer set - C152X1/2TC

Two wing self-guiding TCT cutter ideal for biscuit jointing, 37.2mm diameter X 4.0mm cut. Three ball bearings supplied (12.7mm, 16.0mm and 19.0mm)

D=37.2 mm Cut length=4 mm B=12.7 mm B2=16.0 mm B3=19.0 mm Shank Diameter=1/2 inch Includes:

Price: £33.60

Biscuit jointer set - C152X1/4TC

Two wing self-guiding TCT cutter ideal for biscuit jointing, 37.2mm diameter X 4.0mm cut. Three ball bearings supplied (12.7mm, 16.0mm and 19.0mm)

D=37.2 mm Cut length=4 mm B=12.7 mm B2=16.0 mm B3=19.0 mm Shank Diameter=1/4 inch Includes:

Price: £33.60

Two flute cutter 12.7mm diameter - C153DX1/2TC

Two flute cutter 12.7mm diameter X 50.0mm with centre tip for plunge cutting in abrasive metals, softwood, harwood, MDF, plywood and chipboard.

D=1/2 inch D=12.7 mm Cut length=2 inches Cut length=50 mm Shank Diameter=1/2 inch Includes:

Price: £23.19

Two flute cutter 12.7mm diameter - C153X1/2TC

Two flute cutter 12.7mm diameter X 50.0mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/2 inch D=12.7 mm Cut length=2 inches Cut length=50 mm Shank Diameter=1/2 inch Includes:

Price: £14.90

Two flute cutter 12.7mm diameter - C164X1/2TC

Two flute cutter 12.7mm diameter X 63.0mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/2 inch D=12.7 mm Cut length=2 1/2 inches Cut length=63 mm Shank Diameter=1/2 inch Includes:

Price: £20.97

Guided trimmer 6.35mm diameter x 25.4mm - C168X1/4TC

Guided trimmer 6.35mm diameter X 25.4mm cut for trimming pastic or plywood overlays.

D=1/4 inch D=6.35 mm Cut length=1 inch Cut length=25.4 mm B=6.35 mm A=90 degrees Shank Diameter=1/4 inch Includes:

Price: £13.73

Two flute cutter 12mm diameter - C172X1/2TC

Two flute cutter 12.0mm diameter X 63.0mm cut for softwood, harwood, MDF, plywood and chipboard.

D=15/32 inch D=12 mm Cut length=2 1/2 inches Cut length=63 mm Shank Diameter=1/2 inch Includes:

Price: £20.97

Aquamac 21 Recesser 54.5mm diameter - C207X1/2TC

Aquamac 21 Recesser 46.3 mm diameter. Comes complete with a guide bearing to reduce setting up time and simplify machining operations.

D=46.3 mm D2=34.3 mm C=10.3mm C2=2.7 mm B=28.6 mm OL=90 mm Shank Diameter=1/2 inch Includes:

Price: £50.19

Intumescent cutter set 10mm x 40mm - C208X1/2TC

Neat cut intumescent cutter set, 40mm diameter X 10mm cut for grooves on door frames for intumescent strips.

D=40 mm C=10 mm B=32 mm E=4 mm Shank Diameter=1/2 inch Includes:

Price: £38.02

Intumescent cutter set 10mm x 24mm - C209X1/4TC

Neat cut intumescent cutter set, 24mm diameter X 10mm cut for grooves on door frames for intumescent strips.

D=24 mm C=10 mm B=16 mm E=4 mm Shank Diameter=1/4 inch Includes:

Price: £26.44

Intumescent cutter set 15mm x 24mm - C220X1/4TC

Neat cut intumescent cutter set, 24mm diameter X 15mm cut for grooves on door frames for intumescent strips.

D=24 mm C=15 mm B=16 mm E=4 mm Shank Diameter=1/4 inch Includes:

Price: £27.71

Two flute cutter 12.7mm diameter - TR17DX1/2TC

Two flute cutter for a clean finish, TCT centre tip for drilling abrasive material. 12.7mm diameter X 50.0mm cut.

D=1/2 inch D=12.7 mm C=50 mm OL=93 mm Shank Diameter=1/2 inch Includes:

Price: £25.92

Two flute cutter 12.7 diameter 12.7mm diameter - TR17X1/2TC

Two flute cutter for a clean finish. 12.7mm diameter X 50.0mm cut.

D=1/2 inch D=12.7 mm C=50 mm OL=94 mm Shank Diameter=1/2 inch Includes:

Price: £22.04

Two flute cutter 12.7mm diameter - TR18DX1/2TC

Two flute cutter for a clean finish, TCT centre tip for drilling abrasive material. 12.7mm diameter X 63.0mm cut.

D=1/2 inch D=12.7 mm C=63 mm Shank Diameter=1/2 inch Includes:

Price: £29.80

Two flute cutter 12.7mm diameter - TR18X1/2TC

Two flute cutter for a clean finish. 12.7mm diameter X 63.0mm cut.

D=1/2 inch D=12.7 mm C=63 mm OL=106 mm Shank Diameter=1/2 inch Includes:

Price: £25.39

Two flute cutter 15.9mm diameter - TR19X1/4TC

Two flute cutter for a clean finish. 15.9mm diameter X 19.0mm cut.

D=5/8 inch D=15.9 mm C=19 mm OL=60 mm Shank Diameter=1/4 inch Includes:

Price: £21.51

Two flute cutter 19.1mm diameter - TR20X1/4TC

Two flute cutter for a clean finish. 19.1mm diameter X 25.0mm cut.

D=3/4 inch D=19.1 mm C=25 mm OL=65.5 mm Shank Diameter=1/4 inch Includes:

Price: £21.51

Radius 5mm radius and 18mm diameter - TR21X1/4TC

Radius cutter for edge coves and fluting. 5.0mm radius X 18.0mm cut.

Cut length=18 mm R=5 mm Shank Diameter=1/4 inch Includes:

Price: £20.97

Chamfer V groove cutter angle=45 degrees - TR22X1/4TC

Chamfer and V groove cutter, ideal for fast chamfering to remove edge on timber, or creating a decorative edge. 45 degrees X 12.7mm diameter.

D=1/2 inch D=12.7 mm Overall length=53 mm A=45 degrees Shank Diameter=1/4 inch Includes:

Price: £17.63

Guided trimmer 6.35mm x 12.7 - TR23X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 6.35mm diameter X 12.7mm cut

D=1/4 inch D=6.35 mm Cut length=1/2 inch Cut length=12.7 mm Shank Diameter=1/4 inch Includes:

Price: £15.95

Guided trimmer 6.3mm diameter x 25.4 - TR24X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 6.35mm diameter X 25.4mm cut

D=1/4 inch D=6.35 mm Cut length=1 inch Cut length=25.4 mm Overall length=74.2 mm Shank Diameter=1/4 inch Includes:

Price: £16.57

Guided trimmer 9.5mm diameter x 12.7 - TR25X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 9.5mm diameter X 12.7mm cut

D=3/8 inch D=9.5 mm Cut length=1/2 inch Cut length=12.7 mm Overall length=63 mm Shank Diameter=1/4 inch Includes:

Price: £19.31

Guided trimmer 12.7mm diameter x 25.4 - TR26X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 12.7mm diameter X 25.4mm cut

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Overall length=76.5 mm Shank Diameter=1/4 inch Includes:

Price: £21.51

Guided trimmer triple fluted 12.7X25.4 - TR27X1/4TC

Triple flutted bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 12.7mm diameter X 25.4mm cut

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Shank Diameter=1/4 inch Includes:

Price: £26.44

Guided trimmer 12.7mm x50mm - TR28X1/2TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 12.7mm diameter X 50.0mm cut

D=1/2 inch D=12.7 mm Cut length=50 mm Shank Diameter=1/4 inch Includes:

Price: £38.02

Guided profiler - TR29X1/4TC

Guided profiler for trimming and profiling timber and man made board. 12.7mm diameter X 25.4mm cut.

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Overall length=70.8 mm Shank Diameter=1/4 inch Includes:

Price: £23.19

Guided profiler - TR30X1/2TC

Guided profiler for trimming and profiling timber and man made board. 19.1mm diameter X 50.0mm cut.

D=3/4 inch D=19.1 mm Cut length=50 mm Overall length=95 mm Shank Diameter=1/2 inch Includes:

Price: £43.05

Guided ovolo round over cutter 6.35mm radius - TR31X1/4TC

Bearing guided ovolo cutter, produces a smooth round over profile. 25.4mm diameter, incudes 12.7mm bearing.

D=1 inch D=25.4 mm B=9.5 mm R=6.3 mm Shank Diameter=1/4 inch Includes:

Price: £36.95

Guided ovolo over 9.5mm radius - TR32X1/4TC

Bearing guided ovolo cutter, produces a smooth round over profile. 31.7mm diameter, incudes 12.7mm bearing.

D=31.7 mm B=9.5 mm R=9.5 mm Shank Diameter=1/4 inch Includes:

Price: £39.17

Guided chamfer angle=45 degrees x 31.8mm - TR33X1/4TC

Bearing guided chamfer and V groove cutter, ideal for fast chamfering to remove edge on timber, or creating a decorative edge. 45 degrees X 31.8mm diameter.

D=1 1/4 inches D=31.8 mm Overall length=62 mm B=9.5 mm A=45 degrees Shank Diameter=1/4 inch Includes:

Price: £28.36

Bearing guided rebater 12.7mm - TR34X1/2TC

Bearing guided rebater, includes 3 extra bearings (9.5mm, 15.9mm and 19.1mm)

D=35mm C=12.7mm Shank Diameter=1/2 inch Includes:

Price: £37.48

Biscuit jointer set - TR35X1/2TC

Bearing guided biscuit jointer set. Enables biscuit jointing with timber, man made fibre and partical board. 37.2mm diameter X 4.0mm cut

D=29/64 inch D=37.2 mm Cut length=4 mm B=12.7 mm Shank Diameter=1/2 inch Includes:

Price: £42.41

Biscuit jointer set - TR35X1/4TC

Bearing guided biscuit jointer set. Enables biscuit jointing with timber, man made fibre and partical board. 37.2mm diameter X 4.0mm cut

D=29/64 inch D=37.2 mm Cut length=4 mm B=12.7 mm Shank Diameter=1/4 inch Includes:

Price: £42.41

Two flute cutter 12mm diameter - TR37X1/2TC

Two flute cutter for a clean finish. 12.0mm diameter X 63.0mm cut.

D=12 mm C=54 mm OL=115 mm Shank Diameter=1/2 inch Includes:

Price: £29.77

Two flute cutter 15mm diameter - TR40DX1/2TC

Two flute cutter for a clean finish, TCT centre tip for drilling abrasive material. 15.0mm diameter X 25.0mm cut.

D=15 mm C=25 mm OL=63 mm Shank Diameter=1/2 inch Includes:

Price: £22.56

Two flute cutter 15mm diameter - TR40DX1/4TC

Two flute cutter for a clean finish, TCT centre tip for drilling abrasive material. 15.0mm diameter X 25.0mm cut.

D=15 mm C=25 mm Shank Diameter=1/4 inch Includes:

Price: £22.56

Intumescent cutter set 10mm x 40mm - TR41X1/2TC

Bearing guided intumescent recesser, 40.0mm diameter X 10.0mm cut.

D=40 mm Cut length=10 mm B=32 mm E=4 mm Shank Diameter=1/2 inch Includes:

Price: £38.63

Intumescent cutter set 15mm x 40mm - TR42X1/2TC

Bearing guided intumescent recesser, 40.0mm diameter X 15.0mm cut.

D=40 mm Cut length=15 mm B=32 mm E=4 mm Shank Diameter=1/2 inch Includes:

Price: £39.70

Router Cutter - C121BX1/4TC

Bearing guided template profile for rebating and trimming only. 12.7mm diameter X 9.5mm cut.

Price: £17.30

Router Cutter - TR47X1/2TC

Bearing guided roman ogee, by raising the cutter the top is quickly removed. 25.4mm diameter.

Price: £33.60

13mm Guide Bush / Template Guide (Quick Fastening Lock) - 2609200138

13mm guide bush/template guide suitable for use with Bosch DIY and professional routers: GKF 600; GMF 1400 CE; GMF 1600 CE; GOF 900; GOF 900 ACE; GOF 900 CE; GOF 1600 CE; GOF 2000 CE Professional; POF 800; POF 1100 AE; POF 1200 AE; POF 1300 ACE; POF 1400 ACE.

Price: £13.07

16mm Guide Bush / Template Guide (Quick Fastening Lock) - 2608000471

16mm guide bush/template guide suitable for use with Bosch DIY and professional routers: GKF 600; GMF 1400 CE; GMF 1600 CE; GOF 900; GOF 900 ACE; GOF 900 CE; GOF 1600 CE; GOF 2000 CE Professional; POF 800; POF 1100 AE; POF 1200 AE; POF 1300 ACE; POF 1400 ACE.

Price: £18.30

17mm Guide Bush / Template Guide (Quick Fastening Lock) - 2609200139

17mm guide bush/template guide suitable for use with Bosch DIY and professional routers: GKF 600; GMF 1400 CE; GMF 1600 CE; GOF 900; GOF 900 ACE; GOF 900 CE; GOF 1600 CE; GOF 2000 CE Professional; POF 800; POF 1100 AE; POF 1200 AE; POF 1300 ACE; POF 1400 ACE.

Price: £11.39

24mm Guide Bush / Template Guide (Quick Fastening Lock) - 2609200140

24mm guide bush/template guide suitable for use with Bosch DIY and professional routers: GKF 600; GMF 1400 CE; GMF 1600 CE; GOF 900; GOF 900 ACE; GOF 900 CE; GOF 1600 CE; GOF 2000 CE Professional; POF 800; POF 1100 AE; POF 1200 AE; POF 1300 ACE; POF 1400 ACE.

Price: £15.46

27mm Guide Bush / Template Guide (Quick Fastening Lock) - 2609200141

27mm guide bush/template guide suitable for use with Bosch DIY and professional routers: GKF 600; GMF 1400 CE; GMF 1600 CE; GOF 900; GOF 900 ACE; GOF 900 CE; GOF 1600 CE; GOF 2000 CE Professional; POF 800; POF 1100 AE; POF 1200 AE; POF 1300 ACE; POF 1400 ACE.

Price: £15.46

30mm Guide Bush / Template Guide (Quick Fastening Lock) - 2609200142

30mm guide bush/template guide suitable for use with Bosch DIY and professional routers: GKF 600; GMF 1400 CE; GMF 1600 CE; GOF 900; GOF 900 ACE; GOF 900 CE; GOF 1600 CE; GOF 2000 CE Professional; POF 800; POF 1100 AE; POF 1200 AE; POF 1300 ACE; POF 1400 ACE.

Price: £13.46

Buy Replacement Parts and Accessories for the Bosch 3 60117 800

63 Compatible Accessories Available!

Accessories for Bosch 3 60117 800

Contact Info

Secure Shopping

Our Service

Help And Advice

Your Account

Recently Viewed